DAVIS Sensor Mounting Arm Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Pračky DAVIS Sensor Mounting Arm. Sensor Mounting Arm Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Product # 7702
S
ENSOR
M
OUNTING
A
RM
The Sensor Mounting Arm provides an ideal mounting location for all of your
Davis weather station sensors. This manual is designed to take you through the
process required to assemble and mount the Sensor Mounting Arm. Please take
the time to read through this manual before beginning.
C
OMPONENTS
The Sensor Mounting Arm includes the following components. Please make
sure you have all listed components before continuing.
Sensor Arm
Mounting Bracket
16.5-foot (5 m) Ground Wire
Installation Hardware Kit
a.
One 3/8” Cable Clamp
b.
Four 3/16” Cable Clamps
c.
Three 3/8” Cable Ties
d.
Four 1/4” x 1-1/2”
(38 mm) Lag Screws
e.
Eleven #8 Flat Washers
f.
Six #8 Split Lock Washers
g.
Six #8-32 Hex Nuts
h.
Eight 1/4” Flat Washers
i.
Eight 1/4” Split Lock
Washers
j.
Eight 1/4”-20 Hex Nuts
k.
Four 5/16” Flat Washers
l.
Four 5/16” Split Lock
Washers
m.
Four 5/16”-18 Hex Nuts
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - OMPONENTS

Product # 7702 S ENSOR M OUNTING A RM The Sensor Mounting Arm provides an ideal mounting location for all of your Davis weather station sensors. Th

Strany 2

Page 10 Sensor Mounting Arm 7. Position the U-bolts/saddles on top of the sensor arm on the side farthest from the mounting bracket so the ends of th

Strany 3

Attaching the Anemometer Page 1110. Slide the anemometer arm backwards/forwards until the end of the anemometer arm extends just 1/2” past the second

Strany 4 - TTACHING

Page 12 Sensor Mounting Arm15. Secure the cable clamp and cable in place using an #8 flat washer and an #8-32 hex nut.Tighten the hex nut until the cab

Strany 5 - NEMOMETER

Mounting the Sensor Mounting Arm Page 13Mounting the Sensor Mounting Arm on a Small PipeFollow the instructions below to mount the Sensor Mounting Arm

Strany 6

Page 14 Sensor Mounting ArmMounting the Sensor Mounting Arm on a Large PipeFollow the instructions below to mount the Sensor Mounting Arm on a pipe wi

Strany 7

Grounding the Sensor Mounting Arm Page 15GROUNDING THE SENSOR MOUNTING ARMWe strongly recommend that you ground the sensor arm. You will need the 16.5

Strany 8

Product Number: 7702Davis Instruments Part Number: 7395-091Sensor Mounting ArmRev. C Manual (7/7/99)DI:Weather:Accessories:Sensor Mounting ArmThis pro

Strany 9

Page 2 Sensor Mounting Arm n. Two 1/2” U-Bolts (for anemometer arm) o. Two 1/2” Saddles p. Two 1-1/2” U-Bolts (for pipe with outside diameter between

Strany 10

Assembling the Sensor Mounting Arm Page 3 The Sensor Arm The illustration below shows the sensor arm and indicates which holes are used by the variou

Strany 11 - ATTACH THE CABLE CLAMP

Page 4 Sensor Mounting Arm A TTACHING THE M OUNTING B RACKET In order to attach the mounting bracket to the sensor arm, you will need the sensor

Strany 12 - MOUNTING ON A WOODEN POST

Attaching the Anemometer Page 5 A TTACHING THE A NEMOMETER You may mount the anemometer on either side of the sensor arm. The pre-ferred mounting

Strany 13 - MOUNTING ON A SMALL PIPE

Page 6 Sensor Mounting Arm Attaching the Anemometer Below the Sensor Arm (Preferred) To attach the anemometer below the sensor arm, you will need the

Strany 14 - U-BOLTS AND SADDLES ON PIPE

Attaching the Anemometer Page 7 6. Slide the ends of the U-bolts into the appropriate holes at the end of the sensor arm nearest the mounting bracket

Strany 15 - SAFETY AND BUILDING CODES

Page 8 Sensor Mounting Arm 8. Slide the anemometer arm backwards/forwards until the end of the anemometer arm extends just 1/2” (13 mm) past the sec

Strany 16 - TECHNICAL SUPPORT

Attaching the Anemometer Page 9 Attaching the Anemometer Above the Radiation Shield To attach the anemometer above the sensor arm, you will need the

Komentáře k této Příručce

Žádné komentáře