DAVIS Wireless Repeater 7625 Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro Směrovače DAVIS Wireless Repeater 7625. DAVIS Wireless Repeater 7625 Installation manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Product # 6330
A
NEMOMETER
T
RANSMITTER
K
IT
I
NSTALLATION
M
ANUAL
This manual describes how to install the Anemometer Transmitter Kit for Wire-
less Vantage Pro
TM
. The kit enables you to connect the anemometer from your
Integrated Sensor Suite (ISS) to its own transmitter, so it can be located away
from the ISS and communicate directly with your console/receiver.
C
OMPONENTS
The Anemometer Transmitter Kit includes the following components and
mounting hardware:
1/4" Flat Washers
1/4" Lock Washers
1/4" Hex Nuts
3-Volt
Lithium
Battery
U-Bolts
1/4" x 1-1/2" Lag Screws
8" Cable Ties
4" Cable Tie
Transmitter Shelter
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - RANSMITTER

Product # 6330 A NEMOMETER T RANSMITTER K IT I NSTALLATION M ANUAL This manual describes how to install the Anemometer Transmitter Kit for W

Strany 2 - NSTALLATION

Page 10TESTING TRANSMISSION FROM PROPOSED LOCATIONIt is very important to test reception from the proposed location before perma-nently mounting the a

Strany 3

Mounting the Anemometer Transmitter Page 113. Swivel the anemometer until the arm is pointing north.4. Using an adjustable wrench or 7/16" wrench

Strany 4 - REPARING

Page 12Mounting Transmitter Shelter on a Pole1. While holding the shelter against the pole, place a U-bolt around the pole and through the two holes o

Strany 5

Mounting the Anemometer Transmitter Page 13Mounting Transmitter Shelter on a Vertical Surface1. With a 3/16" (5 mm) drill bit, drill two holes ap

Strany 6 - DIP Switches

Page 14A NOTE ON SECURING CABLESTo prevent fraying or cutting of cables, secure them so they will not whip about in the wind. Secure a cable to a meta

Strany 7

Contacting Davis Instruments Page 15“The wind direction is stuck on north, or displays dashes.”It is likely that there is a short or break somewhere b

Strany 8

Product Numbers: 6330Davis Instruments Part Number: 7395.137 Anemometer Transmitter Kit Installation Manual Rev. A Manual (12/28/00)This product co

Strany 9

Page 2 T OOLS FOR S ETUP In addition to the kit, you will need some or all of the following materials: ✦ Adjustable wrench or 7/16" wrench ✦

Strany 10 - 1/4" Hex Nut

Removing the Anemometer from its Current Location Page 3 R EMOVING THE A NEMOMETER FROM ITS C URRENT L OCATION This step assumes that your I

Strany 11 - 40' of Anemometer Cable

Page 4 If Your ISS is Mounted as a Single Unit (Both Sides Together on a Pole) Unfasten the anemometer: 1. Remove the black rain collector cone fro

Strany 12

Setting the Transmitter ID Page 5 5. Locate the DIP switches. You will work with them during the next installation step. S ENSOR I NTERFACE M ODUL

Strany 13

Page 6 The factory default transmitter ID is ‘1’. Looking at the table below, you can see that means the DIP switches are in the OFF position when ea

Strany 14 - Cable Tie

Setting the Transmitter ID Page 7 Setting Console/Receiver(s) to Same ID 1. Put your console into Setup Mode — press and hold the DONE key and press

Strany 15 - CONTACTING DAVIS INSTRUMENTS

Page 8 If You Do Not See Current Wind Readings First, verify that the console/receiver is powered and is not in Setup Mode (exit Setup Mode by pressi

Strany 16 - SPECIFICATIONS

Choosing a Location for the Anemometer Transmitter Page 9 C HOOSING A L OCATION FOR THE ANEMOMETER TRANSMITTERKeep the following factors in mind

Komentáře k této Příručce

Žádné komentáře